
A bond beam is a horizontal course in a concrete block wall that is filled solid with grout and has steel reinforcing bars running along it. It ties the wall together into one unit, gives roof and floor framing a solid place to bear, and helps the wall resist cracking, wind and earthquake loads.
This guide explains what a bond beam is, where it goes in a wall, how it is built with special block units, how it differs from a lintel, and the construction details that cause the most trouble on site. Sources were checked on November 7, 2026.
What a Bond Beam Is
Despite the name, a bond beam usually does not span an opening like a floor beam. It is a band of reinforced, grouted masonry built into the wall itself. The Masonry Advisory Council’s Masonry Insights: Bond Beams quotes the TMS 402 masonry code definition: a horizontal, sloped or stepped element that is fully grouted, has longitudinal bar reinforcement and is built within a masonry wall. In plain terms, it is a fully grouted horizontal element with one or two bars that gives the wall continuity.
An ordinary block wall is a stack of hollow units held together by mortar. Without continuous horizontal steel, each section between joints can move on its own. A bond beam turns the wall into a single connected element and provides a band of solid concrete where loads can be picked up.
What a Bond Beam Does
- Ties the wall together. Continuous horizontal steel makes the wall segments act as one unit instead of separate stacks of block.
- Gives framing a solid bearing. Roof joists, steel bar joists, beams and floor framing need a solid, grouted course to bear on and anchor into. A bond beam spreads a concentrated load along more of the wall.
- Controls cracking. Horizontal reinforcement limits the width of shrinkage and temperature cracks, and in some designs it is used in place of closer control joints.
- Resists lateral load. In shear walls, especially in higher seismic regions, horizontal reinforcement adds in-plane ductility. A bond beam at a floor or roof can act as a diaphragm chord or collector.
Where Bond Beams Go in a Wall
According to the Mason Contractors Association of America’s MCAA glossary entry for bond beam, bond beams are usually seen at the top of foundation walls, at the tops of walls and at each floor diaphragm connection, and intermediate bond beams are often required in higher seismic design categories. The Masonry Advisory Council adds the top of each parapet and each roof diaphragm. Other locations are set by the structural design:
- Under concentrated loads, such as a beam or girder bearing, to widen the length of wall that shares the load.
- At intervals up the wall where the engineer uses horizontal reinforcement for crack control or seismic requirements.
- At intersecting walls that have to transfer load to each other, where the Masonry Advisory Council notes a maximum bond beam spacing of 48 in on center with bars fully developed on each side.
- Over openings, where a bond beam course is often designed to act as the lintel.
How a Bond Beam Is Built
Bond beam units
A standard stretcher block has full-height cross webs, so a horizontal bar cannot lie through it. Bond beam units either have reduced-height webs made at the plant or knock-out panels the mason breaks out in the field. Both keep vertical cores aligned with the blocks below so vertical bars can pass through. U-shaped lintel units can also form a bond beam, but because they do not take vertical bars without field cutting, they suit unreinforced walls better.
Reinforcing and grout stop
The horizontal bars, usually one or two, are placed in the channel and lapped where they splice. At corners, L-shaped corner bars lapped with the bond beam steel carry continuity around the building. Under a bond beam in a partly grouted wall, a mesh grout stop is laid in the bed joint so grout fills the bond beam without running down into every hollow cell below. Bar sizes and weights are listed in our rebar size chart; the design sets which bars to use.
Grouting
The bond beam course is grouted solid, usually along with the vertical reinforced cells it intersects. Where vertical and horizontal bars meet, the cell can get crowded. The MCAA recommends keeping bond beam steel to the minimum needed so grout can flow and consolidate properly around the bars.
Bond Beam vs Lintel vs Steel Angle
| Element | Location | Main purpose | Material |
|---|---|---|---|
| Bond beam | Continuous courses along the wall | Ties the wall together, bearing, crack and lateral control | Grouted bond beam units with rebar |
| Masonry lintel | Over a door or window opening | Spans the opening and carries the wall above | Grouted lintel or bond beam units with rebar, or precast |
| Steel lintel | Over an opening | Spans the opening, often supporting brick veneer | Steel angle or beam |
A bond beam over an opening, designed with the right reinforcement, is effectively a reinforced masonry lintel. Brick veneer and some block walls use a steel lintel instead, usually an angle. In wood-framed walls the same job is done by a header. Which one is right depends on the opening width, the load above and the wall type.
Bond Beams at Control Joints
Control joints let a block wall shrink without cracking at random. Both sources agree that, in most cases, bond beam reinforcement should stop on each side of a control or expansion joint so the joint can open. The exception is a bond beam acting as a diaphragm chord or collector, which has to stay continuous. In that case the Masonry Advisory Council describes using a smooth dowel debonded on one side so load passes across the joint while the wall can still move.
Bond beam size, bar size, location and the connection of joists or beams to it are part of the structural design. A licensed structural engineer has to design any masonry wall that carries roof, floor or lateral loads, and the work normally needs a permit and inspection.
Bond Beam FAQ
What is the purpose of a bond beam?
It ties a masonry wall together with continuous horizontal steel, provides a solid bearing for framing, and helps the wall resist cracking and lateral loads from wind and earthquakes.
Where is a bond beam required?
Typically at the top of each wall and parapet, at the top of foundation walls and at each floor and roof diaphragm. Intermediate bond beams are added when the design or the seismic category calls for them.
Is a bond beam the same as a lintel?
Not exactly. A bond beam runs along the wall to tie it together. A lintel spans an opening. A bond beam course over an opening can be designed to work as the lintel.
How many rebar go in a bond beam?
Usually one or two horizontal bars, but the number and size are set by the structural design for that wall. They are not a standard that applies to every job.
Should bond beam steel run through control joints?
In most walls, no. It is cut at control and expansion joints so the joint can work. Bond beams that serve as diaphragm chords or collectors are the exception and need a continuous, slip-detailed connection.
Reference information only, not engineering advice. Disclaimer.