Skip to content

Cross Bracing: What It Is, How It Works and Where It’s Used

Cross bracing explained: how X bracing stops a frame racking, why only the tension diagonal works, member sizes from AISC data, and how it compares with others.
Source: AISC Shapes Database v16.0Imperial & metric
Cross Bracing: What It Is, How It Works and Where It's Used

Cross bracing is a pair of diagonal members that cross in an X between two posts, columns or joists, turning a rectangle that could rack sideways into two triangles that cannot. In a steel frame, X bracing carries wind and other sideways (lateral) loads down to the foundation, and in most designs only the diagonal being pulled in tension does the work at any moment.

This guide explains how cross bracing works, where you see it in steel buildings, decks and floors, which members are used for it, and how it compares with other bracing patterns. Sources were checked on November 10, 2026.

How Cross Bracing Works

A frame of posts and beams joined with simple bolted connections behaves like a box with hinged corners. Push the top sideways and the box leans over into a parallelogram. There are three ways to stop that: make the corners rigid (a moment frame), fill the box with a stiff panel (a shear wall or diaphragm), or add a diagonal so the box becomes triangles. Cross bracing is the third option, done twice.

Elevation of one braced bay. Two columns and a beam form a rectangle with an X of two diagonals. A wind load pushes the top of the frame to the right. The diagonal running from the top left down to the bottom right is in tension and carries the load to the foundation. The other diagonal is in compression and, if it is slender, simply goes slack. wind tension slack load goes down the tension diagonal to the foundation beam column
One braced bay under wind from the left. The red diagonal is pulled tight and carries the load. If the wind reverses, the other diagonal takes over.

When wind pushes the top of the frame to the right, one diagonal is stretched and the other is squeezed. Steel is very efficient in tension, but a long, thin bar in compression buckles at a small load. Designers use that to their advantage. With two crossed diagonals, they can assume the compression member does nothing and size each diagonal for tension only. When the wind changes direction, the roles swap.

Steel Construction Info, the reference site run by the UK Steel Construction Institute, puts it this way in its guide to braced frames: with crossed diagonals, “slender bracing members carrying only tension may be provided”, while a single diagonal has to be designed for both tension and compression. The same guide notes that when only the tension diagonals are counted, the floor beams become part of the bracing system and the bay works like a Pratt truss.

Where You See Cross Bracing

Vertical bracing in steel buildings

Most low-rise steel buildings use simple shear connections at the beam ends, so the frame itself has little sideways stiffness. Bracing in a few wall bays does that job instead. The Steel Construction Info guide recommends at least three planes of vertical bracing, placed toward the outside of the building so they also resist twisting, and diagonals at roughly 45 degrees. Narrow bays with steep diagonals make the building more prone to sway.

Roof and floor (plan) bracing

Wind hits the walls, so the load has to travel through the roof or floor to reach the braced bays. A concrete-filled metal deck usually acts as a diaphragm and does this on its own. Where it cannot, such as a light metal roof, horizontal X bracing between the rafters forms a truss in the roof plane. In pre-engineered buildings this is often rod bracing, one of the metal building components you see in a wall or roof bay next to the end wall.

Joist bridging in wood floors

In wood floors, “cross bracing” usually means bridging: small X-shaped pieces of lumber or metal straps set between joists at mid-span. They hold deep joists upright so they do not roll or twist, and they spread a point load to the neighboring joists. This is a different job from lateral bracing of a building frame.

Deck posts

On decks, diagonal knee braces between posts and the beam are common. More bracing is not always better here. The American Wood Council says in its FAQ on diagonal knee braces that they should only be installed at corner posts and that interior posts should not have them. The reason is that bracing makes the deck stiffer, which draws more lateral load into the braced posts, and center posts already carry more vertical load.

What Cross Bracing Is Made Of

Because tension-only diagonals do not need to resist buckling, they can be light. Common choices, from lightest to heaviest:

  • Rods and cables: threaded round bar or wire rope with turnbuckles, used for tension-only bracing in metal buildings and light roofs. They are tightened during erection so they are not loose when the load arrives.
  • Flat bar: simple, cheap and easy to bolt or weld to a plate, but useless in compression.
  • Single and double angles: the traditional bracing member. See angle iron sizes for the full range.
  • Hollow structural sections (HSS): square, rectangular or round tube. Tube resists buckling well for its weight, so it is used where a brace has to work in compression too, including many seismic systems. See HSS sizes.

The table compares a few member sizes that show up in bracing details. Weight, area and radius of gyration (r, a measure of how well the section resists buckling; bigger is better) are from the AISC Shapes Database v16.0 (see our sources and methodology), checked November 10, 2026.

MemberWeight (lb/ft)Area (in²)rx = ry (in)
L2x2x1/43.190.9440.605
L3x3x1/44.91.440.926
L4x4x3/89.82.861.23
HSS3x3x1/48.812.441.11
HSS4x4x1/412.213.371.52
HSS4.000×0.250 (round)102.761.33
Source: AISC Shapes Database v16.0. For a single angle, the axis that controls buckling is the diagonal z-axis, whose radius of gyration is smaller than rx; check it in the database before comparing an angle with a tube in compression.

The table shows why tube wins when compression matters. HSS4x4x1/4 weighs about 2.5 times as much as L3x3x1/4 but has a radius of gyration about 1.6 times larger about the axes listed, and a tube has no weak diagonal axis. For a tension-only brace, the angle or a rod is usually enough, and the connection often governs the size rather than the member.

Connections: Where Bracing Usually Fails

A brace is only as strong as its ends. Diagonals usually land on a gusset plate welded or bolted to the beam-column joint, and the load path runs from brace to bolts to gusset to welds to the column and beam. Each link has to be checked. Points that come up again and again:

  • Net section: bolt holes remove material, so the brace is weaker at the connection than in the middle of its length.
  • Crossing point: where the two diagonals cross they are often bolted together. That connection shortens the unbraced length of each member, which matters if they carry compression.
  • Slack rods: a loose rod lets the frame move before it starts working. Turnbuckles have to be snugged up, and checked after the building is closed in.
  • Bending in the beams: the force in a diagonal has a vertical part that the beam at the top of the bay has to take, so the beam size is part of the bracing design.

Cross Bracing vs Other Lateral Systems

SystemHow it resists sideways loadMain trade-off
X (cross) bracingTwo diagonals per bay; often only the tension diagonal is countedLight members, but the X blocks the whole bay, so no door or window there
Single diagonalOne diagonal per bay working in tension and compressionFewer pieces, but the member must resist buckling
Chevron (inverted V)Two diagonals meet at mid-span of the beamLeaves room for an opening, but puts a point load on the beam
K bracingDiagonals meet at mid-height of the columnIf the compression brace buckles, the unbalanced force pulls the column sideways at mid-height
Moment frameRigid beam-to-column joints, no diagonalsBays stay open, but connections and members are heavier; see moment connections
Shear wall or diaphragmA stiff panel (plywood, concrete, steel deck) fills the bayVery stiff, but the bay is closed and the panel needs good edge attachment

The usual reason not to cross brace a bay is that you need to get through it. Building designers often put X bracing in solid wall bays at the ends of the building and use portal or moment frames where doors and windows go.

Can You Add Cross Bracing Yourself?

For a shed shelf, a workbench or a garden structure, a diagonal or two screwed across a frame is common sense and nobody will run numbers on it. For anything that carries people or a building, it is a different matter. Adding a brace changes where the load goes. It makes one part of the structure stiffer, which pulls more load into that part and its connections and foundation, as the deck post example above shows. Removing a brace that is in the wall of a metal building or garage can leave the frame without its lateral system.

The size of bracing members, their connections and their effect on the rest of the frame must be designed and checked by a licensed structural engineer under your local building code. Treat the member sizes on this page as reference data, not a design.

Cross Bracing FAQ

What is the purpose of cross bracing?

It stops a frame from racking sideways. The X turns a rectangle into triangles, so wind, seismic or other lateral loads are carried along the diagonals down to the foundation instead of bending the posts and connections.

Is X bracing better than a single diagonal?

Not always. X bracing lets each diagonal be designed for tension only, so the members can be slender rods, flats or small angles. A single diagonal uses fewer pieces but must resist compression without buckling, so it needs a stiffer section such as a tube. Which is better depends on the loads, the bay size and whether you need an opening.

What angle should cross bracing be?

Around 45 degrees is the usual target for vertical bracing, according to the Steel Construction Info guide to braced frames. Very steep diagonals in narrow bays are less effective at limiting sway.

Why are rod braces on metal buildings tensioned?

Rods only work in tension. If they are loose, the frame has to move before they take up any load. Turnbuckles or nuts are tightened so the rods are snug and start working right away.

Do floor joists need cross bracing?

Deep or long-span joists often get bridging or blocking to keep them from twisting, and your local code and the joist manufacturer set when it is required. Ask the building department or the engineer of record for your project.

Reference information only, not engineering advice. Disclaimer.

Look up any steel beam size

Search all 339 AISC W, S and HP shapes, compare sizes by depth and work out total weight in seconds.