Skip to content

What Gas Is Used for MIG Welding? Steel, Stainless and Aluminum

What gas is used for MIG welding: C-25 (75/25 argon-CO2) for mild steel, 100% CO2 for thick steel, low-CO2 mixes for stainless and pure argon for aluminum.
Source: AISC Shapes Database v16.0Imperial & metric
What Gas Is Used for MIG Welding? Steel, Stainless and Aluminum

For MIG welding mild and carbon steel, the standard gas is C-25, a mix of 75% argon and 25% carbon dioxide; 100% CO2 is the cheaper alternative that digs deeper but spatters more. Stainless steel needs an argon-rich mix with less than 5% CO2, and aluminum is welded with pure argon or an argon-helium mix.

Below is what each gas does, which one to pick for steel, stainless and aluminum, and the setup mistakes that cause porosity and spatter. Manufacturer sources were checked on November 10, 2026.

Why MIG Welding Needs a Shielding Gas

Molten steel reacts quickly with oxygen and nitrogen in the air. Left unprotected, the weld pool picks up gas that comes out as holes (porosity) and turns the bead brittle and dirty. In MIG welding, properly called gas metal arc welding (GMAW), a solid wire feeds through the gun while gas flows out of the nozzle around it, pushing air away from the arc and the pool until the metal freezes.

Cross-section of a MIG gun nozzle above a steel plate. The solid wire runs down the middle through the contact tip. Shielding gas flows down between the contact tip and the nozzle wall and spreads over the arc and the weld pool, keeping the surrounding air away. nozzle gas flows down contact tip wire arc and pool base metal
The gas leaves the nozzle around the wire and forms a shield over the arc and weld pool. A draft or a nozzle full of spatter breaks that shield.

The gas does more than keep air out. It also changes how the arc behaves: how hot and wide it is, how deep it melts into the base metal, how much spatter it throws and how the wire transfers into the pool. That is why the choice depends on the metal you are welding.

The Gases and What Each One Does

Argon

Argon is an inert gas: it does not react with the weld. It gives a smooth, stable arc and is the base of almost every MIG mix. On its own it is the standard gas for aluminum, but pure argon on carbon steel gives a narrow, poorly wetted bead, which is why a reactive gas is added for steel.

Carbon dioxide (CO2)

CO2 is a reactive gas. It makes a hotter, harsher arc that penetrates deeper into steel, and it is the cheapest shielding gas. The cost is more spatter and a rougher bead. It also adds carbon and oxidizes the pool, which is fine for carbon steel but not for stainless.

Helium

Helium is inert like argon but makes a hotter arc. It is added to argon for aluminum and stainless when deeper penetration or faster travel is needed. Because it is so light, it needs a higher flow rate and costs more.

Which MIG Gas to Use: Quick Chart

MaterialCommon gasWhySource
Mild / carbon steel75% argon / 25% CO2 (C-25)Best all-round choice: least spatter, best bead appearance, less burn-through on thin metalMiller
Mild / carbon steel, thicker sections100% CO2Deeper penetration and lowest gas cost; more spatter and a rougher beadMiller
Stainless steelTri-mix (argon, helium, CO2) or 98% argon / 2% CO2Keeps CO2 under 5% so the weld does not pick up excess carbonMiller
Aluminum100% argonThe most common aluminum shielding gasHobart
Aluminum, heavier work75% helium / 25% argonDeeper root penetration and less porosity, at a higher flow rate and costHobart

Gas for MIG Welding Mild Steel

Most structural and shop work, including A36 steel plate, angle and channel, falls into this group. Miller’s guide to MIG welding mild steel calls C-25 “the best all-purpose shielding gas for carbon steel” and says it produces the least spatter. The same page says 100% CO2 gives deeper penetration but more spatter and a rougher bead.

In practice the choice looks like this:

  • Thin sheet, auto body, visible welds: C-25. The softer arc is easier to control and less likely to blow through.
  • Thick plate, farm repair, cost-sensitive production: 100% CO2 is workable if you can live with more cleanup.
  • Not sure: start with C-25. It is the gas most small machines and welding charts are set up around.

Miller pairs this with ER70S-3 wire for all-purpose work, or ER70S-6 when the steel is dirty or rusty and needs more deoxidizers. Its suggested starting flow rate is 20 to 25 cubic feet per hour (cfh).

Galvanized steel uses the same gas, but the zinc coating causes porosity and toxic fumes. Our guide to welding galvanized steel covers the prep and ventilation.

Gas for MIG Welding Stainless Steel

Do not use C-25 or straight CO2 on stainless. The carbon from the CO2 ends up in the weld and lowers corrosion resistance. Miller’s article on MIG welding stainless steel says to use a gas with less than 5% CO2. It names a tri-mix of argon, helium and CO2 as a popular choice, with more helium for conventional MIG and more argon for pulsed MIG, and says a 98% argon / 2% CO2 mix also works well.

Many shops TIG weld stainless instead when appearance matters. See welding stainless steel for the full comparison of processes, filler metals and heat control.

Gas for MIG Welding Aluminum

Aluminum gets no CO2 at all. Hobart Brothers’ aluminum welding guide on shielding gases says pure argon is the most commonly used shielding gas, and lists a 75% helium / 25% argon mix for MIG when deeper root penetration and less porosity are wanted. It notes that helium mixes need higher flow rates because helium is so light.

Aluminum also needs a spool gun or push-pull gun on most machines, because soft aluminum wire tangles in a long liner. The gas is only one part of the setup.

Can You MIG Weld Without Gas?

Not with solid wire. Without gas, a solid wire weld will be full of porosity. What you can do is switch to self-shielded flux-cored wire, which carries its own shielding inside the wire and needs no cylinder. It works outdoors in wind where gas would blow away, but it leaves slag and more spatter. See flux core welding for the details, and MIG vs TIG welding if you are still choosing a process.

Gas Setup Problems That Look Like Bad Welding

  • Porosity in every weld: empty cylinder, closed valve, wrong gas, a leak in the hose or fittings, or a draft from a fan or open door blowing the shield away.
  • Porosity that comes and goes: spatter built up in the nozzle, which disturbs gas flow. Clean the nozzle and use anti-spatter.
  • Too much flow: more is not better. A very high flow can become turbulent and pull air into the shield.
  • Frozen regulator on CO2: straight CO2 cools sharply as it expands, and a regulator not meant for it can ice up. Use a regulator rated for CO2.
  • Working in a small, closed space: argon, CO2 and helium all displace oxygen. Ventilate, and never weld in a tank or pit without a confined-space plan.

Welds on structural members, such as beam connections, columns and stair stringers, also have to meet the welding procedure and inspection requirements of the job. Any weld that carries structural load should be designed and approved by a licensed structural engineer, and made by a welder qualified for that procedure.

MIG Welding Gas FAQ

What is the best gas for MIG welding steel?

For most mild steel work, 75% argon / 25% CO2 (C-25). Miller calls it the best all-purpose shielding gas for carbon steel. Straight CO2 is the budget option for thicker steel.

Can I use pure argon for MIG welding steel?

It will make a weld, but the bead tends to be narrow and poorly tied in. Steel MIG gases include some CO2 (or oxygen) to stabilize the arc and wet the bead out. Save pure argon for aluminum and for TIG welding.

Is MIG gas the same as TIG gas?

Not usually. TIG welding uses pure argon (or argon-helium) on almost everything, because the tungsten electrode would be damaged by reactive gases. MIG on steel uses argon-CO2 mixes. Only for aluminum do the two processes share the same gas.

What flow rate should I set for MIG welding?

Miller suggests 20 to 25 cfh as a starting point for mild steel. Raise it a little in drafty conditions, and follow the wire maker’s data sheet for helium mixes and aluminum, which need more.

Why are my MIG welds full of holes?

That is porosity, and gas coverage is the usual cause: an empty cylinder, a leak, a draft, a clogged nozzle or the wrong gas. Rust, oil and galvanizing on the base metal cause it too, so clean the joint before welding.

Reference information only, not engineering advice. Disclaimer.

Look up any steel beam size

Search all 339 AISC W, S and HP shapes, compare sizes by depth and work out total weight in seconds.