
A beam bridge is the simplest kind of bridge: a deck carried on horizontal beams that span from one support to the next, with each beam resting on an abutment or pier at its ends. The beams carry traffic loads by bending, so the top of each beam is squeezed in compression and the bottom is stretched in tension.
Beam bridges make up most of the short highway and road crossings you drive over without noticing, from creek crossings to highway overpasses. This guide explains how they work, how far they span, what they are built from, and how they compare with truss, arch and suspension bridges.
How a Beam Bridge Works
Load on the deck goes into the beams, the beams bend and carry it sideways to their ends, and the supports carry it straight down into the foundations. There is no cable pulling up and no arch pushing outward: every support simply takes a downward reaction. That is why beam bridges are cheap and quick to build, and also why their span is limited. As a beam gets longer, its bending moment grows with the square of the span, so the beam has to get much deeper and heavier to keep up.
Simple span vs continuous span
In a simple-span bridge each beam ends at every support, so each span acts on its own. In a continuous bridge the beams run unbroken over the interior piers. Continuity lets the beams share load between spans, which reduces the maximum bending moment and usually allows shallower beams, but it puts tension in the top of the beam over each pier and makes the design more involved.
Composite action
On most modern steel beam bridges the concrete deck is tied to the top flange of each beam with welded shear studs. The deck and beam then bend together as one composite section, with the concrete taking much of the compression. That makes a given steel beam stiffer and stronger than it would be on its own.
Beams vs Girders in Bridges
Bridge engineers use both words, and the difference is mostly about size and how the member is made. A rolled beam is a standard wide flange shape straight from the mill. A plate girder is built up by welding a web plate between two flange plates, so it can be made deeper and heavier than any rolled shape. Our article on girder vs beam vs joist covers the terms in buildings, where the same distinction applies.
The Short Span Steel Bridge Alliance’s page on rolled beams and plate girders says rolled wide flange beams come in lengths up to 120 feet and that plate girders can span more than 300 feet (checked October 2026). Its steel bridge basics page defines short span bridges as those under 140 feet and lists the usual options for them as corrugated pipe and plate structures, rolled beams, plate girders and trusses.
How Far Can a Beam Bridge Span?
There is no single number, because span depends on the load, the beam depth that fits under the deck, the number of beams and the material. As a rough guide drawn from the sources above:
| Beam type | Where it is used | Span notes |
|---|---|---|
| Timber beams or glulam | Trails, farm and forest roads | Short spans; limited by available beam depth |
| Rolled steel wide flange beams | Rural road and county bridges, overpasses | Rolled lengths up to 120 ft; spliced for continuous spans |
| Prestressed concrete girders | Highway overpasses and river crossings | Standard precast shapes used over a wide range of spans |
| Steel plate girders | Longer highway and rail spans | Can exceed 300 ft per the SSSBA |
| Steel box girders | Curved ramps, long continuous spans | Closed section resists twisting on curves |
Once spans go well beyond what girders can do economically, designers switch to trusses, arches, cable-stayed or suspension bridges, which carry load through members in pure tension or compression rather than in bending.
A Real Example: Seven W24x131 Beams
The SSSBA describes the Meacham Road Bridge in Washington County, Oregon: a single 75 ft span carried by seven W24x131 rolled steel beams under an 8 in high-performance concrete deck, about 25 ft wide in total (checked October 2026). The designers chose the girder spacing to keep the superstructure shallow, which left more open area under the bridge for the creek.
For scale, here are the published dimensions of that beam from the AISC Shapes Database v16.0 (checked October 2026):
| Property | W24x131 (imperial) | W610x195 (metric) |
|---|---|---|
| Weight | 131 lb/ft | 195 kg/m |
| Depth, d | 24.5 in | 622 mm |
| Flange width, bf | 12.9 in | 328 mm |
| Web thickness, tw | 0.605 in | 15.4 mm |
| Flange thickness, tf | 0.96 in | 24.4 mm |
| Moment of inertia, Ix | 4,020 in⁴ | 1,670 × 10⁶ mm⁴ |
| Plastic modulus, Zx | 370 in³ | 6,060 × 10³ mm³ |
That is a 2-foot-deep beam weighing about 9,800 lb for a 75 ft length, and it sits in the middle of the W24 family. You can compare it with lighter and heavier sections on our W24 beam sizes page or across all depths in the wide flange beam size chart. These numbers are for illustration only: bridge beams are designed to AASHTO bridge specifications for moving truck loads, fatigue and deflection, not to building-span tables.
What Beam Bridges Are Made Of
- Steel. Rolled wide flanges and welded plate girders. Light for their strength, quick to erect, and easy to strengthen or repair later. Corrosion protection comes from paint, galvanizing or weathering steel, which forms a protective rust layer and is widely used for unpainted bridge girders.
- Prestressed concrete. Precast girders with tensioned steel strands that pre-compress the bottom of the beam. Common on highways because they need little maintenance.
- Reinforced concrete. Cast-in-place slabs and T-beams for short spans.
- Timber. Sawn or glued-laminated beams for low-traffic and pedestrian bridges.
Beam Bridge vs Other Bridge Types
| Type | How it carries load | Typical role | Main trade-off |
|---|---|---|---|
| Beam / girder | Bending in horizontal members | Short and medium spans | Simple and cheap, but beams get deep fast as span grows |
| Truss | Tension and compression in a triangulated frame | Medium spans, rail bridges | Light for its span, but many joints to inspect and paint |
| Arch | Compression along a curve, pushing outward on its ends | Medium to long spans over gorges | Needs ground that can resist the outward thrust |
| Cable-stayed | Deck hung from cables running straight to towers | Long spans | Tall towers and complex construction |
| Suspension | Deck hung from main cables draped between towers | The longest spans | Heavy anchorages and high cost |
Small Beam Bridges on Private Land
Farm, ranch and driveway crossings are often built from salvaged or new steel beams. The same rules apply as for a road bridge: the beams have to carry the heaviest vehicle that will ever cross, including fuel and delivery trucks and emergency vehicles, and the abutments have to sit on ground that will not wash out. Span charts for floor beams in buildings, like our steel beam span chart, are not meant for vehicle loads.
Any bridge that carries people or vehicles must be designed by a licensed structural engineer, who sizes the beams, deck, bearings and abutments and checks the site’s flood and permit requirements. Do not size a bridge beam from a general article or a building table.
Beam Bridge FAQ
What is a beam bridge in simple terms?
A deck laid on horizontal beams that rest on supports at each end. It is the same idea as a plank laid across a stream, scaled up with steel, concrete or timber beams.
What are the advantages of a beam bridge?
It is simple to design and build, uses standard members, puts only vertical load on its supports and is quick to erect. Those traits make it the usual choice for short crossings.
What are the disadvantages of a beam bridge?
Span is limited because bending grows quickly with length, so long crossings need intermediate piers or a different bridge type. Piers in a river can also be expensive and restrict flow and navigation.
Are I-beams used in bridges?
Yes. The wide flange shapes used in buildings, often called I-beams, are also used as rolled bridge beams, and deeper bridges use welded plate girders with the same I-shaped cross-section.
What is the difference between a beam bridge and a girder bridge?
Structurally they work the same way, through bending. “Girder bridge” usually means larger built-up plate or box girders, while “beam bridge” covers any deck on horizontal beams, including rolled shapes.
Reference information only, not engineering advice. Disclaimer.