Skip to content

Steel Plate Weight Chart: Weight per Square Foot by Thickness

Steel plate weighs 40.83 lb per square foot per inch of thickness. Chart of plate weights by thickness and sheet size, plus the formula in lb and in kg.
Source: AISC Shapes Database v16.0Imperial & metric
Steel Plate Weight Chart: Weight per Square Foot by Thickness

Carbon steel plate weighs 40.83 lb per square foot for every inch of thickness, so 1/4 in plate is about 10.2 lb/ft², 1/2 in plate about 20.4 lb/ft² and 1 in plate about 40.8 lb/ft². A standard 4 ft x 8 ft sheet of 1/4 in plate therefore weighs about 327 lb.

Below is a steel plate weight chart by thickness, with weights per square foot, per standard sheet size and in metric, followed by the formula so you can work out any size of plate yourself.

Steel Plate Weight Chart

All weights are calculated from a carbon steel unit weight of 490 lb/ft³ and rounded. Sheet weights are for the full 4×8 (32 ft²), 4×10 (40 ft²) and 5×10 (50 ft²) sizes. Metric thickness is the exact conversion of the inch size, not a metric stock thickness.

Thickness (in)Thickness (mm)lb/ft²4×8 sheet (lb)4×10 sheet (lb)5×10 sheet (lb)kg/m²
3/164.87.6624530638337.4
1/46.410.2132740851049.8
5/167.912.7640851063862.3
3/89.515.3149061276674.8
1/212.720.426538171,02199.7
5/815.925.528171,0211,276124.6
3/419.130.629801,2251,531149.5
7/822.235.731,1431,4291,786174.5
125.440.831,3071,6332,042199.4
1-1/431.851.041,6332,0422,552249.2
1-1/238.161.251,9602,4503,062299.1
250.881.672,6133,2674,083398.8

Thinner material is normally sold by gauge rather than by fractional thickness. Convert the gauge to inches with our steel gauge thickness chart and then use the same formula below.

Steel Plate Weight Formula

Weight is volume times density. Carbon steel weighs 490 lb per cubic foot, the value listed for steel in the H-20 table of weights of building materials hosted by Ohio University (checked October 2026). Our density of steel guide shows the same figure in lb/in³ and kg/m³ and checks it against AISC shape weights.

A one-foot by one-foot square of steel plate with thickness t inches. Its volume is t divided by 12 cubic feet, and multiplying by 490 pounds per cubic foot gives 40.83 times t pounds per square foot. 12 in (1 ft) 12 in t volume = 144 × t in³ = t ÷ 12 ft³ weight = 490 × t ÷ 12 = 40.83 × t lb/ft² metric: 7.85 × t (mm) = kg/m²
One square foot of plate t inches thick weighs 40.83 × t lb. Not to scale.

Imperial

Weight (lb) = length (ft) × width (ft) × thickness (in) × 40.83

The 40.83 comes from 490 lb/ft³ divided by 12 in per ft. If your dimensions are all in inches, use length × width × thickness × 0.2836, where 0.2836 lb/in³ is the same density per cubic inch.

Metric

Weight (kg) = length (m) × width (m) × thickness (mm) × 7.85

Steel’s density of 7,850 kg/m³ means each millimeter of thickness adds 7.85 kg per square meter.

Worked Examples

A 24 in x 36 in piece of 3/8 in plate

Area is 2 ft × 3 ft = 6 ft². Weight is 6 × 0.375 × 40.83 = 91.9 lb. Checking with inches: 24 × 36 × 0.375 × 0.2836 = 91.9 lb.

A 12 in x 12 in x 3/4 in base plate with four holes

The solid plate weighs 1 × 0.75 × 40.83 = 30.6 lb. Each 13/16 in hole removes π × (0.406)² × 0.75 = 0.39 in³, or about 0.11 lb, so four holes take off less than half a pound. For estimating, ignore small holes; for a plate with large cutouts, subtract the cutout area before multiplying. Our base plate guide explains how these plates are sized and anchored.

A triangular gusset

A right-triangle gusset with 12 in legs in 1/2 in plate has an area of 12 × 12 ÷ 2 = 72 in², or 0.5 ft². Weight is 0.5 × 0.5 × 40.83 = 10.2 lb. See the gusset plate guide for where these are used.

Plate Strips and Flat Bar

For long narrow pieces it is easier to work in pounds per linear foot. A strip 1 ft long has a volume of width × thickness × 12 in³, so:

Weight (lb/ft) = width (in) × thickness (in) × 3.40

A 6 in wide strip of 1/2 in plate is 6 × 0.5 × 3.40 = 10.2 lb/ft, so a 20 ft length weighs about 204 lb. The same rule works for flat bar: a 2 in × 1/4 in bar weighs 2 × 0.25 × 3.40 = 1.7 lb/ft.

Steel Plate vs Aluminum Plate Weight

The same Ohio University table lists aluminum at 171 lb/ft³, which works out to 14.25 lb/ft² per inch of thickness, about 35% of the weight of steel plate of the same size.

Thickness (in)Steel (lb/ft²)Aluminum (lb/ft²)4×8 steel (lb)4×8 aluminum (lb)
1/85.101.7816357
1/410.213.56327114
1/220.427.13653228
140.8314.251,307456

Lighter does not mean interchangeable. Aluminum is also much less stiff and has different strength, so an aluminum plate swapped in for a steel one usually has to be thicker to do the same job. That substitution is a design decision, not a weight calculation.

Why Real Plate Weights Differ

Rolling tolerances

Plate is not rolled to exactly its nominal thickness. Permitted variations in dimensions and weight for structural plate are set in ASTM A6/A6M, the general requirements specification for rolled structural steel bars, plates, shapes and sheet piling (scope checked October 2026). The calculated weights above are nominal; a mill’s or service center’s scale weight can be a little different.

Grade and alloy

Grade changes strength, not weight. A36 plate and A572 Grade 50 plate of the same size weigh the same, since both are carbon or low-alloy steel at 490 lb/ft³. ASTM A36 covers carbon steel shapes, plates and bars of structural quality (scope checked October 2026); our A36 steel guide covers its properties. Stainless plate is a few percent heavier for the common austenitic grades, and aluminum plate is about one third the weight.

Tread plate

Raised-pattern floor plate is ordered by the thickness of the base plate, and the raised lugs add weight on top of that. Use the supplier’s published weight for tread plate rather than this chart; our diamond plate guide has more detail.

Using Plate Weights Safely

Plate weights are useful for freight quotes, picking a hoist or lifting clamp, and estimating material cost by the pound. A 4×8 sheet of 1/2 in plate is about 650 lb, which is well beyond a two-person lift, so plan the handling before it arrives. Lifting gear must be rated for the actual load. If the plate is part of a structure, such as a base plate, splice plate or stiffener, its thickness and welds have to be designed and checked by a licensed structural engineer; weight tells you nothing about whether a plate is strong enough.

Steel Plate Weight FAQ

How much does a 4×8 sheet of 1/4 inch steel plate weigh?

About 327 lb: 32 ft² × 0.25 in × 40.83 lb/ft² per inch.

How much does a square foot of 1 inch steel plate weigh?

About 40.8 lb. That is 144 in³ of steel at 0.2836 lb/in³.

How do I calculate steel plate weight in kg?

Multiply length in meters by width in meters by thickness in millimeters, then by 7.85. A 1.2 m × 2.4 m sheet of 10 mm plate weighs 1.2 × 2.4 × 10 × 7.85 = 226 kg.

Does stainless steel plate weigh more?

Slightly. Type 304 is about 7,900 kg/m³ and 316 about 8,000 kg/m³, against 7,850 for carbon steel, so 316 plate is roughly 2% heavier than carbon steel plate of the same size.

Is the chart accurate enough for shipping?

It is close enough for estimating, but rolling tolerances mean actual plate can weigh a little more or less. Use the supplier’s scale weight on the bill of lading for freight and for crane picks near the limit of the equipment.

Reference information only, not engineering advice. Disclaimer.

Look up any steel beam size

Search all 339 AISC W, S and HP shapes, compare sizes by depth and work out total weight in seconds.