
Post and beam construction is a way of building where a frame of vertical posts and horizontal beams carries the roof and floors, instead of closely spaced load-bearing stud walls. Because the frame does the structural work, the walls between posts can be open, glazed or moved, which is why post and beam is popular for open-plan homes, barns, pavilions and timber-framed buildings.
This guide explains how post and beam framing carries load, how it differs from stick framing and timber framing, the materials and connections used, how the frame is kept from racking sideways, and the trade-offs to weigh before choosing it. Sources were checked on November 9, 2026.
What Post and Beam Construction Is
The Timber Framers Guild’s page Timber Framing: The Basics puts it simply: in post and beam structures, upright posts support horizontal beams. The members can be round logs, squared timber or, in modern buildings, engineered wood and steel. They are often joined with metal brackets or plates rather than carved joints.
The key idea is that loads are gathered into a few large members rather than spread through many small ones. In a stick-framed house, every stud in a bearing wall carries a share of the roof. In a post and beam building, the roof load collects on beams and travels down a handful of posts to individual footings. If the terms beam, girder and joist are fuzzy, our girder vs beam vs joist guide sorts them out.
How Loads Travel Through a Post and Beam Frame
Follow the load from the top down:
- Roof sheathing and rafters, or purlins, collect snow, dead load and wind and pass it to the beams.
- Beams span between posts and bend under that load. Their depth and material set how far they can span.
- Posts take the beam reactions as compression and carry them straight down.
- Each post lands on a footing or pier sized for a concentrated load, not a continuous wall footing. Our pier and beam foundation guide covers the same idea at floor level.
Post and Beam vs Timber Frame vs Stick Framing
The terms overlap, and builders use them loosely. The Timber Framers Guild describes timber framing as a specialized version of timber post and beam, joined with mortise and tenon joints held by wooden pegs, and notes that the line between the terms blurs as code requirements push even traditional frames toward engineered connectors.
| System | What carries the load | Typical joints | Interior walls |
|---|---|---|---|
| Stick framing | Many closely spaced studs, joists and rafters | Nails, screws, light metal connectors | Some walls are load-bearing |
| Post and beam | A few large posts and beams | Steel plates, brackets, bolts, sometimes wood joinery | Mostly non-bearing, free to move |
| Timber frame | Large timbers in a pre-cut frame | Mortise and tenon with wooden pegs, sometimes hidden steel | Mostly non-bearing |
| Post-frame (pole barn) | Posts set in the ground or on piers, with girts and purlins | Bolts, nails, metal brackets | Usually none |
Materials for Posts and Beams
Wood
Solid sawn timbers such as Douglas fir or white oak give the classic look, but large pieces can be hard to source dry and tend to check and shrink as they season. Engineered options are more predictable. A glulam beam is laminated from smaller boards, can be made long and curved, and is common for exposed ridge and floor beams.
Steel
Steel post and beam frames use wide flange beams and square or round tube posts. They span farther for the same depth, do not shrink, and are common where a long clear opening is needed or where a wood beam would be too deep. Typical members include W-shape beams and HSS (hollow structural section) posts, covered in our HSS sizes chart and our guide to steel columns.
The table lists a few light shapes that appear in residential and small commercial frames, with dimensions from the AISC Shapes Database v16.0. They are examples to show scale, not recommendations for any particular span or load.
| Shape | Role | Weight (lb/ft) | Depth (in) | Flange width (in) |
|---|---|---|---|---|
| W8X18 | Beam | 18 | 8.14 | 5.25 |
| W10X22 | Beam | 22 | 10.2 | 5.75 |
| W12X26 | Beam | 26 | 12.2 | 6.49 |
| HSS4X4X1/4 | Post | 12.21 | 4 (square) | 4 |
| HSS5X5X1/4 | Post | 15.62 | 5 (square) | 5 |
| HSS6X6X1/4 | Post | 19.02 | 6 (square) | 6 |
Connections: Where Post and Beam Frames Succeed or Fail
Because a few members carry everything, each joint carries a lot. Common connections include:
- Post caps and bases: steel brackets that seat the beam on the post and anchor the post to the footing, holding it against uplift and sliding.
- Knife plates and bolts: a steel plate slotted into the timber and through-bolted or pinned, often hidden for a clean look.
- Traditional joinery: mortise and tenon, dovetail and lap joints secured with pegs in timber-framed work.
- Bolted or welded steel plates: for steel frames, cap plates, base plates and shear tabs.
Our post to beam connection guide walks through the main options for both wood and steel.
Keeping the Frame From Racking
A frame of posts and beams joined with simple connections is good at carrying vertical load but has little resistance to being pushed sideways by wind or earthquakes. Left unbraced, it can lean over like a parallelogram. Steel designers deal with the same issue in braced frames: the Steel Construction Institute’s page on braced frames explains that beams and columns with nominally pinned connections are designed for vertical load, while a separate bracing system provides stability and resists lateral loads.
Post and beam buildings get that lateral resistance in one or more ways:
- Knee braces between posts and beams, the traditional timber frame approach.
- Shear walls sheathed with plywood or OSB in some bays.
- Diagonal rods or steel X-bracing in hidden or exposed bays.
- Moment-resisting connections that make the joints themselves rigid, at higher cost.
Many modern frames are enclosed in structural insulated panels (SIPs), which wrap the outside of the frame so the timber stays visible inside. Whether the panels count toward lateral bracing is a design decision, not an assumption.
Pros and Cons of Post and Beam Construction
Advantages
- Open floor plans with few or no interior bearing walls.
- Large windows and openings, since walls between posts do not carry load.
- Exposed structure as the main architectural feature.
- Flexible remodeling, because non-bearing partitions can be moved later.
Disadvantages
- Concentrated loads need properly sized footings under each post.
- Larger members and specialty connections usually cost more than standard dimensional lumber, and need a crane or careful rigging to set.
- Wood movement: large solid timbers shrink and check as they dry, which can affect finishes and joints.
- Engineering is required. Fewer members means less redundancy, so each beam, post, connection and brace has to be designed.
Beam size, post size, footing size, connections and bracing all have to be designed for the actual spans, snow, wind and seismic loads at your site. A licensed structural engineer has to size and check the frame, and the building needs a permit and inspection. Span charts are useful for early planning only.
Post and Beam FAQ
What is the difference between post and beam and timber frame?
Timber framing is a type of post and beam that uses carved wood joinery such as pegged mortise and tenon joints. Post and beam more broadly includes frames joined with metal brackets, bolts and plates, in wood or steel.
Is post and beam construction more expensive?
Usually, because the members are larger, connections are more specialized and the frame needs engineering and often a crane. The difference depends heavily on design, material and region.
Can post and beam use steel?
Yes. Steel wide flange beams with tube or wide flange posts are common where long spans, shallow beams or slim posts are needed. Wood and steel are often mixed in the same building.
Do post and beam homes need load-bearing walls?
Not for vertical load, which the frame carries. Some walls or bays may still be designed as shear walls to brace the building against wind and earthquakes.
How far can a post and beam span?
It depends on beam material, depth, spacing and load, so there is no single answer. Deeper beams and steel span farther. A structural engineer sets the actual sizes for each project.
Reference information only, not engineering advice. Disclaimer.